Oil hot water boiler ASME
  • Oil hot water boiler
  • Oil fired hot water boiler
  • oil hot water boilers
  • oil hot water boiler for sale

Best Oil Hot Water Boilers for Sale

Price: $4,000.00 - $15,000.00

An oil hot water boiler is the most advanced type of boiler system. It has been widely used in the world for decades. This guide will discuss what oil-fired hot water boilers are, how they work, their efficiency ratings, and how much it costs to install them.

  • Rated thermal power: 0.7 - 28 Mw
  • Rated thermal efficiency: 91 - 96%
  • Operating pressure: ≤ 2.5 MPa
  • Available fuel: diesel oil, light oil, heavy oil, etc

Low Nitrogen Environmental Protection, High
Efficiency & Energy Saving

  • Exceptional Resistance to Corrosion

    The condensing heat transfer component within the oil hot water boiler furnace is crafted from aluminum-silicon alloy, renowned for its remarkable resistance to corrosion.

  • Modular Boiler Design

    This design enhancement significantly improves the system's load adjustment capability, consequently raising overall system operational efficiency. This results in reduced fuel consumption and operating costs, optimizing the adjustment range within a wide spectrum from 20% to 100%.

  • Environmentally Responsible

    The heating system of the oil hot water boiler adopts an innovative, environmentally friendly combustion technique. It employs full fuel and air premixing while incorporating surface combustion technology, leading to heightened combustion efficiency. This results in emissions that meet stringent environmental standards, with NOx levels kept at or below 30mg/m3.

  • Advanced Control Technology

    The burner is equipped to achieve proportional adjustments. It can continuously adapt its output load based on the user's hot water requirements, enabling seamless modulation of burner output. This ensures the boiler consistently operates at a high level of combustion efficiency.

Oil Hot Water Boiler Parameters

Types Thermal power Steam pressure Thermal efficiency Fuel Power requirement Length * Width * Height Weight Chimney
Unit Mw MPa % V/Hz mm t mm
CWNS0.7-95/70-Y.Q 0.7 ≤2.5 91-96 diesel oil, light oil, heavy oil, etc 380/50 3370 * 1660 * 1830 2.32 300
CWNS1.4-95/70-Y.Q 1.4 3450 * 1820 * 2030 3.04 350
CWNS2.1-95/70-Y.Q 2.1 4200 * 1940 * 2420 5.04 350
CWNS2.8-95/70-Y.Q 2.8 5230 * 1940 * 2340 5.24 450
CWNS4.2-95/70-Y.Q 4.2 6550 * 2340 * 3640 10.08 550
CWNS5.6-95/70-Y.Q 5.6 7580 * 2550 * 3780 16.4 700 * 550
WNS0.7-1.0/95/70-Y.Q 0.7 3490 * 1710 * 2880 3.33 300
WNS1.4-1.0/95/70-Y.Q 1.4 4320 * 1930 * 2200 4.66 350
WNS2.8-1.0/95/70-Y.Q 2.8 5340 * 1990 * 3460 8.14 450
WNS4.2-1.0/95/70-Y.Q 4.2 6540 * 2330 * 3630 14.21 600 * 450
WNS5.6-1.0/95/70-Y.Q 5.6 7260 * 2580 * 3950 19.85 600 * 450
WNS7-1.0/95/70-Y.Q 7 7630 * 2730 * 4410 24.72 700 * 450
WNS14-1.0/95/70-Y.Q 14 9340 * 3660 * 4690 46.42 950 * 600

An oil hot water boiler is the most advanced type of boiler system. It has been widely used in the world for decades. This guide will discuss what oil-fired hot water boilers are, how they work, their efficiency ratings, and how much it costs to install them.

What is an oil hot water boiler?

An oil hot water boiler, also known as an oil-fired hot water boiler, is a heating system that uses oil as a fuel source to heat water. It is a type of central heating system commonly found in residential and commercial buildings.

How does an oil hot water boiler work?

Here’s a simplified explanation of how an oil hot water boiler typically works:

  1. Fuel Supply: The boiler is connected to a fuel supply, usually an oil storage tank. Heating oil is drawn from the tank and delivered to the burner.
  2. Combustion Process: The burner ignites the heating oil, creating a flame within the combustion chamber. The flame heats the heat exchanger, which is responsible for transferring heat from the combustion gases to the water.
  3. Heat Transfer: The heated combustion gases flow through the heat exchanger, transferring their heat energy to the water surrounding the exchanger’s tubes or plates. The heat exchanger’s surface area maximizes the heat transfer efficiency.
  4. Circulation: The heated water is then circulated through the building’s heating system using a circulator pump. This distributes the hot water to radiators, baseboard heaters, or other heating elements, providing heat to the living spaces.
  5. Temperature Control: A thermostat monitors the temperature in the building and signals the boiler to cycle on or off to maintain the desired temperature. This ensures that the boiler operates efficiently and provides consistent heating.
  6. Exhaust: After the heat transfer process, the cooled combustion gases are exhausted through a flue or chimney.

Oil hot water boiler heating system

What is the efficiency of oil fired hot water boiler?

The efficiency of an oil-fired hot water boiler can vary depending on several factors, including the design, age, and maintenance of the boiler, as well as the specific model and its combustion technology. Generally, the efficiency of oil-fired hot water boilers can range from around 80% to 95% or higher.

The efficiency of oil fired hot water boiler is very important. It directly affects how much energy will be consumed and the cost to use it. The efficiency of oil fired hot water boiler can be calculated using the formula: Efficiency = Heat Out/Heat In × 100%.

Is an oil hot water boiler expensive to run?

The operating cost of a oil-fired hot water boiler can vary depending on several factors, including the fuel type, boiler efficiency, fuel price, and usage patterns. To estimate the operating cost, you’ll need to consider the following steps:

  1. Determine the fuel consumption rate of the boiler, typically measured in units like cubic feet per hour (CFH) or gallons per hour (GPH).
  2. Obtain the current fuel price per unit. This information can usually be obtained from local fuel suppliers or energy providers.
  3. Calculate the hourly fuel consumption by multiplying the fuel consumption rate by the cost per unit.
  4. Multiply the hourly fuel consumption by the number of operating hours per day to get the daily fuel cost.

best oil hot water boiler

How much is an oil hot water boiler in 2023?

The cost of an oil hot water boiler can vary depending on several factors, including the brand, model, capacity, features, and geographic location. Generally, oil hot water boilers can range in price from around $4,000 to $15,000 or more.

Size (Tons/hr) Fuel Type Efficiency Price Range
1 – 5 Oil 80% $4,000 – $6,000
6 – 10 Oil 85% $5,000 – $8,000
11 – 15 Oil 87% $6,000 – $10,000
16 – 20 Oil 90% $8,000 – $12,000
21+ Oil 92% $15,000+

How much does it cost to install an oil-fired water heater?

On average, the installation cost for an oil-fired water heater can range from $1,500 to $3,500 or more. This cost typically includes labor, materials, and any necessary permits. However, it’s important to note that this is just an average estimate, and prices can vary significantly based on your location and specific installation requirements.

The cost to install an oil-fired water heater can vary depending on several factors, including the size and type of the water heater, the complexity of the installation, local labor rates, and any additional materials or services required.

oil hot water boiler for sale

 

Conclusion.

If you’re considering looking for an oil hot water boiler then check out our guide above which will give you all the information needed before making a decision!

FAQs.

What is oil hot water heating?

Oil hot water heating is a heating system that uses oil as a fuel source to heat water, which is then circulated through radiators or baseboard heaters to provide warmth in a building.

How does a hot oil boiler work?

A hot oil boiler operates by burning oil to heat a chamber, which in turn heats water. This hot water is then pumped through the heating system, releasing heat through radiators or baseboards, providing warmth to the space.

Is oil hot water heat efficient?

Oil hot water heat can be efficient when well-maintained. Modern oil boilers are designed to 95%, but efficiency can vary based on factors like boiler age, maintenance, and insulation in the building.

How much oil to heat hot water?

Typically, it takes about 0.03 to 0.04 liters of oil to raise the temperature of 1 liter of water by 1 degree Celsius (or 1.8 degrees Fahrenheit). The amount of oil required to heat hot water varies depending on the size and efficiency of the boiler and the hot water temperature.

Get your best price

Quickly compare 3 FREE quotes

  • Engineer quick quote
  • The overall delivery speed is fast
  • Financial choice
  • Low installation costs and cost savings
Get Quotes Now
It only takes 30 seconds
25 years+ of boiler R&D

25 years+ of boiler R&D

More than 20 innovative technologies